All projects

01 / Electric vehicles / Safety electronics

Making system state visible.

UCD Formula Student

In development

Monitoring, fault detection and integration for the electrical systems of a Formula Student electric race car.

01—SENSE.
DETECT.
INDICATE.
TSAL / Functional concept · illustrative, not project hardware
MY ROLE

Electrical team · one of three engineers on the TSAL design

TOOLS & TECHNOLOGIES
KiCadLTspiceLogisim Evolution
EVIDENCE STATUS

Based on reported project involvement

01 / CONTEXT

Overview

The Tractive System Active Light (TSAL) is part of the vehicle’s safety-related electronics. My work connects voltage and relay monitoring with digital fault logic, PCB development and wider vehicle integration. The work described here is ongoing; design release and completed validation are not claimed.

The engineering problem

A useful status indication depends on more than a single signal. The design work considers tractive-system voltage, precharge relay monitoring and fault detection together, with attention to reliability and how the circuitry integrates with the rest of the car.

02 / CONTRIBUTION

My role & responsibilities

  • Working with two other engineers on the TSAL design.
  • Developing precharge relay monitoring, fault detection and digital latching logic.
  • Working on voltage detection and tractive-system status monitoring.
  • Designing and laying out PCBs in KiCad; using Logisim Evolution and LTspice for development.
  • Soldering, wiring and bench testing circuits, with vehicle-level motherboard integration involving TSAL, BSPD and support circuitry.

Requirements & constraints

  • Tractive-system context: 302.4 V nominal, 352.8 V maximum.
  • Safety-related status and fault monitoring must be considered at system level.
  • Interfaces with precharge monitoring and a motherboard that includes BSPD and supporting circuits.
  • Final thresholds, isolation arrangements, component choices and applicable rule references are not yet published.

03 / THE SYSTEM

Architecture

01

Monitor

Tractive-system voltage · precharge relay state

02

Evaluate

Fault detection · digital logic · latching

03

Indicate & integrate

TSAL · vehicle motherboard interfaces

Functional summary of the work described, not a released schematic or a verified safety architecture. Signal polarity, thresholds and implementation details are intentionally omitted.

04 / IMPLEMENTATION

Hardware, software & interfaces

Logic development

Digital logic gates and latching are being developed for fault detection. Logisim Evolution supports the circuit-level logic work.

Circuit and PCB development

LTspice is used for circuit analysis and simulation, and KiCad for schematic and PCB development. Physical work includes soldering, wiring and bench testing.

Vehicle integration

The motherboard brings TSAL, BSPD and support circuitry into a larger electrical system. My involvement includes working through this vehicle-level integration.

05 / ENGINEERING REASONING

Decisions & trade-offs

01

Monitoring and fault retention

Fault detection and latching are part of the design scope. A worked example explaining the chosen latch behaviour, reset conditions and alternatives will be added after the design is documented.

02

From logic to a physical system

The logic model, circuit simulation and PCB layout address different parts of the problem. Final interface assumptions and evidence linking these stages remain to be published.

Challenges & lessons

The central challenge is carrying monitoring and fault behaviour through logic, circuits and vehicle interfaces. A specific design iteration, its evidence and the lesson learned will be added here once documented.

06 / EVIDENCE

Testing & verification

What is known, what remains to be demonstrated.

  • Bench testing is part of my reported work; dated procedures and results are not yet published.
  • To document: logic truth tables, fault-injection cases and latch/reset behaviour.
  • To document: simulation conditions, sensing behaviour and motherboard interface checks.
  • No vehicle-level safety validation, regulatory compliance or completed release is claimed.

07 / WORK IN PROGRESS

Current status & next steps

In development

Active design and integration work. The brief establishes hands-on involvement, but does not identify a completed PCB revision or a signed-off validation milestone.

  1. Publish a reviewed block diagram and design rationale.
  2. Add approved schematic excerpts and PCB renders.
  3. Document bench setup, test cases and observed results.
  4. Record integration milestones and distinguish each completed revision from ongoing work.

KEEP EXPLORING

Team BeaconDiscuss my work